Eco Glass

 

Brilliant Recycled Glass Textured Finish
Contains 66% Recycled Content
No Fading
Only from Master Wall®

 

Eco Glass Finishes are used as the final color and texture coat for various Master Wall® Systems or Interiors. Eco Glass Finish is a unique mix of recycled colored glass with a brilliant shimmer that won't fade over time. Eco Glass is available in five-gallon (19L) pails and is applied over Primecoat primer.

 

Coverage

• 75 square feet (7 square meters)

*Coverages are estimated and vary

 

Weight: 65 lbs (29.5 kg)

 

Working Time: 1 hour under normal room temperature and humidity.

 

Drying Time: 8-12 hours to set, 48-72 hours to dry under normal room temperature and humidity.

 

Application/Storage Temperatures: 50°F (10°C) to 110°F (43°C)

 

Shelf Life: 2 years under normal conditions.

 

Approved Substrates

• Master Wall® Base Coats
  Stucco
  Prepared & Base Coated Surfaces of:
  Brick
  Concrete
  Masonry
  Others approved in writing
  

 

Application Procedure

General—Air and substrate temperature for application of Eco Glass must be 50°F (10°C) or higher and must remain 50°F (10°C) or higher for a minimum of 24 hours. Working and drying times are based upon normal room temperature conditions and will vary with temperature and humidity.

Preparation - The substrate must be approved by Master Wall Inc., clean, dry, structurally sound and free of efflorescence, oil, grease, form release agents and curing compounds or anything that would affect bond. Painted surfaces are not acceptable and must be removed. Concrete and surfaces should cure for a minimum of 28 days. Stucco should be cured until clean, dry and hard—typically 14 days.

Interior drywall should be finished and made ready for paint. Prime surfaces with tinted Sanded Primecoat primer prior to finishing with Eco Glass.

 

Base Coats - Must be flat, dry hard, and free of efflorescence. Master Wall® base coats must cure a minimum of 12 hours before application of Eco Glass. Substrates of brick, masonry or concrete should be leveled smooth using either Master Wall base coats or stucco.

 

Mixing—Thoroughly stir the Eco Glass Finish using a heavy duty 1/2" (12.7 mm) drill at 400-500 rpm and a paddle similar to a Wind-lock B-MTW mixer. Small amounts of clean, potable water may be added to obtain a workable consistency. To avoid texture or coverage variations, add the same amount of water to each pail. Don't exceed 12 ounces (0.35L) of water per pail.

Application—Prime the surface with tinted Master Wall Primecoat. Allow Primecoat to dry a minimum of 12 hours prior to finish coat application.

 

Trowel Application—Apply the Eco Glass Finish to the clean, dry and cured base coat with a stainless steel trowel. Trowel finish uniformly then scrape down to a thickness equal to the size of the aggregate. Float to eliminate trowel marks and irregularities.

 

Spray Application—Using a conventional plaster hopper gun or a proven pump, spray two coats of the finish over the primed base coat to achieve the desired texture. Use a circular overlapping pattern keeping the spray gun at a 90º angle to the surface maintaining the same distance to the wall at all times. Be cautious of flooding an area with too much finish as it may appear shinier when it dries.

 

Clean Up—Tools and equipment can be cleaned with soapy water while the finish coat is still wet.

 

For Professional Results
Apply finish coats away from direct sunlight.

Surfaces exposed to the weather must be sloped (6:12 minimum).

Finishes are intended for the approved substrates listed above and should not be applied directly to gypsum board or insulation board products except as noted above.

 

 

Information contained in this product data sheet conforms to the standard detail recommendations and specifications for the installation of Master Wall® Inc. products and is presented in good faith. Master Wall Inc. assumes no liability, expressed or implied as to the architecture, engineering, or workmanship of any project. This information may be concurrent with, or superseded by other applicable documents, such as specifications and details. Contact Master Wall® Inc. for the most current product information.